Distortion control in multi pass dissimilar GTAW process using Taguchi ANOVA analysis

 
 
 
  • Abstract
  • Keywords
  • References
  • PDF
  • Abstract


    The present study is to observe the distortion development in the weldment of Inconel 625 to SS316L multipass weldments. In this work two-level factors such as welding process, filler wire and root gap were employed with L4 orthogonal array. The welding has been carried out with continuous current and pulsed current gas tungsten arc welding process implementing ERNiCrMo-3 and ERNiCr-3 fillers rods respectively. The fractional factorial experimentation was analysis of variances (ANOVA), it was carried out to observe the critical parame-ter which influence distortion caused in the weldments. The quality of welds has been evaluated by X-Ray Radiography test. The results show that welding process and filler wire are contributing more in the distortion.

     

     

  • Keywords


    Dissimilar Materials; GTAW Multipass Welding; Vernier Height Gauge; Distortion.

  • References


      [1] Mackwood, A.P. and Crafer, R.C., 2005. Thermal modelling of laser welding and related processes: a literature review. Optics and Laser Technology, 37(2), pp.99–115. https://doi.org/10.1016/j.optlastec.2004.02.017.

      [2] Pan LK, Wang CC, Hsiao YC, Ho KC.2005. Optimization of Nd:YAG laser welding onto magnesium alloy via Taguchi analysis. Optics & Laser Technology, 37(1), pp.33–42. https://doi.org/10.1016/j.optlastec.2004.02.007.

      [3] Akella, S., Kumar, B.R. and Krishnaiah, Y., 2013. Optimisation of welding process parameters for distortion control with Taguchi approach. International Journal of Precision Technology, 3(2), p.206. https://doi.org/10.1504/IJPTECH.2013.053305.

      [4] Anawa, E.M. and Olabi, A.G., 2008. Using Taguchi method to optimize welding pool of dissimilar laser-welded components. Optics & Laser Technology, 40(2), pp.379–388. https://doi.org/10.1016/j.optlastec.2007.07.001.

      [5] Deng, D., 2009. FEM prediction of welding residual stress and distortion in carbon steel considering phase transformation effects. Materials & Design, 30(2), pp.359–366. https://doi.org/10.1016/j.matdes.2008.04.052.

      [6] Deng, D. and Murakawa, H., 2008. FEM prediction of buckling distortion induced by welding in thin plate panel structures. Computational Materials Science, 43(4), pp.591–607. https://doi.org/10.1016/j.commatsci.2008.01.003.

      [7] Deng, D., Murakawa, H. and Shibahara, M., 2010. Investigations on welding distortion in an asymmetrical curved block by means of numerical simulation technology and experimental method. Computational Materials Science, 48(1), pp.187–194. https://doi.org/10.1016/j.commatsci.2009.12.027.

      [8] Moraitis, G.A. and Labeas, G.N., 2008. Residual stress and distortion calculation of laser beam welding for aluminum lap joints. Journal of Materials Processing Technology, 198(1-3), pp.260–269. https://doi.org/10.1016/j.jmatprotec.2007.07.013.

      [9] Muralimohan, C.H., Haribabu, S., Hariprasada Reddy, Y., Muthupandi, V. and Sivaprasad, K., Joining of AISI 1040 Steel to 6082-T6 Aluminium alloy by friction welding. Journal of Advances in Mechanical Engineering and Science, 1(1), pp.57–64.

      [10] Vemanaboina, H., Akella, S. and Buddu, R.K., 2014. Welding Process Simulation Model for Temperature and Residual Stress Analysis. Procedia Materials Science, 6, pp.1539–1546. https://doi.org/10.1016/j.mspro.2014.07.135.

      [11] Akella, S., Vemanaboina, H. and Kumar Buddu R., 2016. Heat Flux for Welding Processes: Model for Laser Weld. Sreyas International Journal of Scientists and Technocrats, 1(1), pp.10–15. https://doi.org/10.24951/sreyasijst.org/2016011002.

      [12] Saravanan, V., Rajakumar, S. and Muruganandam, A., 2016. Influence of tool rotation speed on macrostructure, microstructure and mechanical behavior of dissimilar friction stir welded AA2014-T6 and AA7075-T6 Aluminium alloys. Journal of Advances in Mechanical Engineering and Science, 2(4), pp.19–24. https://doi.org/10.18831/james.in/2016041003.

      [13] Phillip J Ross, Taguchi Techniques for Quality Engineering, Tata McGraw Hill, 2008.

      [14] Ranjith Roy, “A Primer An Taguchi Methods”, Van Nostrand Reinhold, Newyork,(1990).

      [15] Welding Engineering and Technology by R. S. Parmar, Edition-2, Khanna Publishers, 2010.


 

View

Download

Article ID: 12607
 
DOI: 10.14419/ijet.v7i3.12607




Copyright © 2012-2015 Science Publishing Corporation Inc. All rights reserved.