Optimization cutting parameters when grinding X12M steel using Hai Duong grinding wheel
Abstract
This paper presents an experimental research to build two regressions they are relationship between surface roughness of workpiece and cutting parameters when grinding grinding X12M steel using Hai Duong grinding wheels. Two types of Hai Duong grinding wheel using in this paper are Cn46.TB1.G. V1.400x40x203x50m/s and Cn46.CV1.G. V1.400x40x203x35m/s. Three cutting parameters are considered in this paper are depth of cut, feed rate and velocity of workpiece. Genetic algorithm had used to find value of cutting parameters for minimum value of surface roughness. This work had get optimization value of cutting parameters for each case of a pair of workpiece – wheel.
About this article
Keywords
- Cylindrical Grinding
- Surface Roughness
- Cutting Parameters
- X12M Steel
- Optimization
- Hai Duong Grinding Wheel.
References
[1] Kirankumar Ramakantrao Jagtap, S.B.Ubale, M.S.Kadam (2011), “Optimization of cylindrical grinding process parameters for AISI 5120 steel using Taguchi method”, International Journal of Design and Manufacturing Technology, Vol. 2, Number 1, pp. 47-56.
[2] Hoang Tien Dung, Do Duc Trung,Nguyen van Thien, Nguyen Nhu Tung, Ngo Cuong (2019), “Optimization Cutting Parameters When Grinding ШX15 Steel Using Hai Duong Grinding Wheel”, International Journal of Mechanical and Production Engineering Research and Development, Vol. 9, Issue 4, pp. 155-162 https://doi.org/10.24247/ijmperdaug201917.
[3] Pawan Kumar, Anish Kumar, Balinder Singh (2013), “Optimization of Process Parameters in Surface Grinding Using Response Surface Methodology”, International Journal of Research in Mechanical Engineering & Technolog, Vol. 3, Issue 2, pp. 245-252.
[4] M. Janardhan and A. Gopala Krishna (2012), “Multi – Objective optimization of cutting parameters for surface roughness and metal removal rate in surface grinding using response surface methodology”, International Journal of Advances in Engineering & Technology, Vol. 3, Issue 1, pp. 270-283.
[5] Aman thakur, V.Sahni (2017), “Optimization of traverse cut cylindrical grinding process parameters of treated EN-8 steel”, International journal of Advance Research in Science and Engineering, Vol. 6, Issue .12, pp.1512-1523.
[6] Taranvir Singh, Parlad Kumar, Khushdeep Goyal (2014), “Optimization of Process Parameters for Minimum Outof-Roundness of Cylindrical Grinding of Heat Treated AISI 4140 Steel”, American Journal of Mechanical Engineering, Vol. 2, No. 2, pp.34-40. https://doi.org/10.12691/ajme-2-2-1.
[7] Turkkan N, Floating Point Genetic Algorithm—Genetik V2.01, 2001, http://www.umoncton.ca/turk/logic.htm.
[8] P. Krajnik, J. Kopac, A. Sluga (2005), “Design of grinding factors based on response surface methodology”, Journal of Materials Processing Technology, vol. 162–163, pp. 629–636. https://doi.org/10.1016/j.jmatprotec.2005.02.187.
[9] Saravanan R. and Sachithanandam M (2001), “Genetic Algorithm (GA) for Multivariable Surface Grinding Process Optimisation Using a Multi – objective function model”, International Journal of Advanced Manufacturing Technology, pp. 330-338. https://doi.org/10.1007/s001700170167.
[10] Phan Bui Khoi, Do Duc Trung, Ngo Cuong, Nguyen Dinh Man (2015), “Research on Optimization of Plunge Centerless Grinding Process using Genetic Algorithm and Response Surface Method”, International Journal of Scientific Engineering and Technology, Volume 4, Issue 3, pp. 207-211. https://doi.org/10.17950/ijset/v4s3/319.