Concrete Surfacing Using Surface Energy of Nanoparticles

 
 
 
  • Abstract
  • Keywords
  • References
  • PDF
  • Abstract


    This article considers scientific and practical principles of concrete surfacing. As it was found, such production can be done by impregnating the surface of high-strength concrete with silica sol, measuring the surface energy of nanoparticles introduced. A technique was introduced for calculating surface energy of sols, so was the range of energy necessary to create concrete with a shock resistant surface, determined by measurement and calculation. The content contains possible reactions resulting in new phases in the concrete top during the impregnation with silica sol. Physical and mechanical characteristics of surfaced concrete were also outlined ad considered, so were the XRD data and electron microscopy data. Various types of energy used to surface concrete until high dynamic strength were compared. This article provides evidence that surface energy of sol nanoparticles can be considered as an independent alternative source.

     

     


  • Keywords


    surfaced concrete, silica sol, surface energy, concrete impregnation, surface hardiness.

  • References


      [1] Schuster, B. E., Aydelotte, B. B., Leavy, R. B., Satapathy, S., & Zellner, M. B. (2015). Concurrent velocimetry and flash x-ray characterization of impact and penetration in an armor ceramic. Procedia Engineering, 103, 553-560.

      [2] Grujicic, M., Pandurangan, B., Angstadt, D. C., Koudela, K. L., & Cheeseman, B. A. (2007). Ballistic-performance optimization of a hybrid carbon-nanotube/E-glass reinforced poly-vinyl-ester-epoxy-matrix composite armor. Journal of materials science, 42(14), 5347-5359.

      [3] Silnikov, M. V., Vasilyev, N. N., Spivak, A. I., Barkov, D. D. (2018). The method of obtaining bulletproof material from ballistic fabric. Military Enginery
      Series: Counter-terrorism technical devices,
      9, 104-107.

      [4] Huang, F. L., & Zhang, L. S. (2007). Investigation on ballistic performance of armor ceramics against long-rod penetration. Metallurgical and Materials Transactions A, 38(12), 2891-2895.

      [5] Coleman, S. P., Hernandez-Rivera, E., Behler, K. D., Synowczynski-Dunn, J., & Tschopp, M. A. (2016). Challenges of engineering grain boundaries in boron-based armor ceramics. JOM, 68(6), 1605-1615.

      [6] Zhitnyuk, S. V., Makarov, N. A., & Guseva, T. V. (2014). New silicon carbide based ceramic armor materials. Glass and ceramics, 71(1-2), 6-9.

      [7] Galanov, B. A., Kartuzov, V. V., Grigoriev, O. N., Melakh, L. M., Ivanov, S. M., Kartuzov, E. V., & Swoboda, P. (2013). Penetration resistance of B4C-CaB6 based light-weight armor materials. Procedia Engineering, 58, 328-337.

      [8] Kremenchugsky, M. V., Savkin, G. G., Malinov, V. I., Rachkovsky, A. I., Smorchkov, G. Yu. (2008). Ultra-light armored ceramic materials from nanostructured powders of boron carbide. Rossijskie nanotehnologii [Russian Nanotechnologies]. 3(3-4), 141-146.

      [9] Banerjee, A., Dhar, S., Acharyya, S., Datta, D., & Nayak, N. (2017). Numerical simulation of ballistic impact of armour steel plate by typical armour piercing projectile. Procedia engineering, 173, 347-354.

      [10] Bester, J. N., & Stumpf, W. E. (2013). Plasticity and Ballistic Characterization of a New Armour Steel. In Dynamic Behavior of Materials, 1 (pp. 109-122).

      [11] Artsruni, A. A., Tsurgozen, L. A., Makhov, B. F. (2010). Aluminum and problems of armor protection. In the Recent Problems of Protection and Safety. Proceedings of the 13th All-Russian Scientific and Practical Conference. Armored Vehicles and Weapons. Russian Academy of Missile and Artillery Sciences (RARAN), 3, 95-102.

      [12] Gasqueres, C., Nissbaum, J. (2011). Ballistic performance and failure mode of high performance 2139-T8 and 7449-T6 Aluminium alloys, 26th International Symposium on Ballistics. Miami, September 12-16, 1289-1295.

      [13] Svatovskaya, L., Sychova, A., Sychov, M., Okrepilov, V. (2016). Quality Improvement of Concrete Articles. MATEC Web of Conferences 53, 01023.

      [14] Sychova, A. M., Svatovskaya, L. B., Mjakin, S. V., Vasiljeva, I. V. (2009). Modification of fillers for cements (Book Chapter). Electron Beam Modification of Solids: Mechanisms, Common Features and Promising Applications, 4. 35-37.

      [15] Sychova, A. M., Svatovskaya, L. B., Mjakin, S. V., Vasiljeva, I. V. (2009). Activation of aqueous phase at cement and concrete solidification (Book Chapter). Electron Beam Modification of Solids: Mechanisms, Common Features and Promising Applications, 5, 39-47.

      [16] Starchukov, D. S., Kozin, P. A., Stepanova, I. V., Mandritsa, D. P., Ishakov, Sh. Sh., Kovalev, F. E. (2014). Engineering and chemical fundamentals behind the production of high-strength concrete with sol-containing additives: a monograph. A.F. Mozhaysky's Military-Space Academy, 108.

      [17] Zaytsev, G. P. (2012). Corundum armor ceramics: production and application. Expert Union. 3. Electronic resource: http://www.unionexpert.ru/index.php/news/item/287-alumina-bronekeramika-experience-of-production-and-use

      [18] Eliseev, V. S., Kravchenko, A. D., Yarosh, V. V. (2001). Ballistic effect of high-hard materials. Military Enginery Series: Composite non-metal materials in mechanical engineering, 3-4, 15-26.

      [19] Svatovskaya, L., Kabanov, A., & Sychov, M. (2017). Soling, Aerating and Phosphating for Soil Strengthening and Detoxication. Procedia engineering, 189, 398-403.

      [20] Svatovskaya, L., Kabanov, A., & Sychov, M. (2017). Lithosynthesis of the properties in the transport construction on the cement base. In IOP Conference Series: Earth and Environmental Science, 90(1), p.12

      [21] Svatovskaya, L., Urov, O., & Kabanov, A. (2017). Geoecoprotective technology of transport construction using silica sol absorption method. Procedia engineering, 189, 454-458.

      [22] Butt, Yu. M., Sychev, M. M., Timashev, V. V. (1980). Chemical technology for binders. Moscow: Vysshaya shkola, 472.

      [23] Shabanova, N. A., Sarkisov, P. D. (2004). Fundamentals of nanodispersed sol-gel technology. Akademkniga Publishing House, 208.

      [24] Babushkin, V. I., Matveyev, G. M., Mchedlov-Petrossyan, O. P. (1986). Thermodynamics of silicates: 4th Edition [updated and revised]. Moscow: Stroiizdat, 408.

      [25] Gorshkov, V. S., Timashev, V. V., Saveliev, V. G. (1981). Physical and chemical analysis of binders. Moscow: Vysshaya shkola, 336.

      [26] Van Damme, H. (2018). Concrete material science: Past, present, and future innovations. Cement and Concrete Research.

      [27] Vlasov, A. S. (2004). High-speed penetration into silicon carbide ceramics with different porosity. Journal of Technical Physics, 74(5), 62-65

      [28] Vlasov, A. S. (1999). Kinetics of high-speed penetration into high brittle media. Solid State Physics, 41(10), 1785-1787.

      [29] Antoun, T., Curran, D. R., Seaman, L., Kanel, G. I., Razorenov, S. V., & Utkin, A. V. (2003). Spall fracture. Springer Science & Business Media.


 

View

Download

Article ID: 23030
 
DOI: 10.14419/ijet.v7i4.7.23030




Copyright © 2012-2015 Science Publishing Corporation Inc. All rights reserved.