2-D Strength Prediction of Single-row Multi-bolted Joints Woven Fabric Kenaf Composites

  • Authors

    • Khairi Supar
    • Hilton Hilton Ahmad
    2018-07-04
    https://doi.org/10.14419/ijet.v7i3.7.16198
  • Multi-bolt, Woven fabric, Kenaf fibers, XFEM.
  • Implementation of multi-bolts arrangements in structures connections are commonplace in steel design to allow for joint efficiency and stronger connections. Woven fabric kenaf fibers are potentially used as reinforcement in composite materials due to excellent specific strength, renewability and less hazardous during handling as compared to commercial fibers. A two-dimensional Extended Finite Element Method (XFEM) framework of single-row multi-bolted joints has been developed to study the stress distribution and predict the joint bearing stress at failure. Stress distribution among adjacent bolts were compared along the hole boundary and net-tension plane, suggesting net-tension failure occurred at end-bolt. The predicted bearing strength from finite element modelling are validated against experimental framework. The testing series under investigated consists of four datasets from single-row 2 bolts and 3 bolts single-lap joints.  Current study showed that the XFEM models demonstrated good agreements with the experimental results.

     

     

  • References

    1. [1] N. Saba, M.T. Paridah, and M. Jawaid, “Mechanical properties of kenaf fibre reinforced polymer compositeâ€: a review. Constr. Build. Mater, 76, 2015, pp. 87–96.

      [2] J. George, M.S. Sreekala, and S. Thomas, “A review on interface modification and characterization of natural fiber reinforced plastic compositesâ€, Polymer Engineering & Science, 41, 2001, pp. 1471–1485.

      [3] J.H. Crews, C.S. Hong, and I.S. Raju, “Stress Concentration Factors for Finite Orthotropic Laminates with a Pin-loaded Holeâ€. 1-40, 1981: NASATechnology Paper 1862, 1981.

      [4] D. Cunningham, K.A. Harries, and A.J. Bell, “Open-hole tension capacity of pultruded GFRP having staggered hole arrangementâ€. Engineering Structures, 95, 2015, pp. 8–15.

      [5] C.T. McCarthy, and P.J. Gray, “An analytical model for the prediction of load distribution in highly torqued multi-bolt composite jointsâ€. Composite Structures, 93(2), 2011, pp. 287–298.

      [6] C.T. McCarthy, M.A. McCarthy, and V.P. Lawlor, “Progressive damage analysis of multibolt composite joints with variable bolt-hole clearancesâ€. Compos Part B – Eng ;36(4), 2005, pp. 290–305.

      [7] H. Ahmad, A.D. Crocombe, and P.A. Smith, “Strength Prediction of Notched Composite Plates using a Cohesive Zone Approachâ€, Advanced Material Research, Vol. 845, 2014, p. 199-203.

      [8] H. Ahmad, A.D. Crocombe, and P.A. Smith, “Strength Prediction in CFRP Woven Laminate Bolted Double-Lap Joints under Quasi-static Loading using XFEMâ€. Composites Part A :56, 2013, pp. 192-202.

      [9] H. Ahmad, “Stress Distribution in Composite Double-Lap Bolted Joints Incorporating with Clamp-Up². Applied Mechanics and Materials, Vol: 660, 10, 2014, pp. 152-156, ISSN:16627482.

      [10] H. Ahmad, “Stress Distribution of Secondary Bending in Single-Lap Bolted Joints with Dissimilar Joining Plates and Plate Types², Journal Teknologi, Vol: 78, 6, 2016, pp. 1-7, ISSN:2180-3722.

      [11] C.T. McCarthy, and P.J. Gray, “A global bolted joint model for finite element analysis of load distributions in multi-bolt composite jointsâ€, Composite : Part B, 41, 2010, pp. 317-325.

      [12] H. Ahmad, A.D. Crocombe, and P.A. Smith, "Physically Based Finite Element Strength Prediction in Notched Woven Laminates under Quasi-static Loading". Plastics, Rubber and Composites :42(3), 2013, pp. 93-100.

      [13] A. Kontolatis, “Failure of Composite Bolted Joints Made from Woven Fabric GFRP Compositeâ€, MSc dissertation, Guildford: University of Surrey, 2000.

      [14] N.A. Rahman, Z.M. Jaini, and N.N.M. Zahir, “Fracture Energy of Foamed Concrete by Means of the Three-Point Bending Tests on Notched Beam Specimensâ€, APRN Journal of Engineering and Applied Sciences, Vol: 10, 2015, pp. 6562-6570.

      [15] L.Y. Fong, H.A. Ghafar, N.A. Rahman, and D. Yeoh, “Connection Performance for LVL-Concrete Composite Floor Systemâ€, Applied Mechanics and Materials, Vol: 773-773, 2015, pp. 954-963.

  • Downloads

  • How to Cite

    Supar, K., & Hilton Ahmad, H. (2018). 2-D Strength Prediction of Single-row Multi-bolted Joints Woven Fabric Kenaf Composites. International Journal of Engineering & Technology, 7(3.7), 21-24. https://doi.org/10.14419/ijet.v7i3.7.16198