Prediction the wear of sliding bearings

  • Abstract
  • Keywords
  • References
  • PDF
  • Abstract

    The problem of developing a calculation-experimental method for calculating wear of a sliding bearing based on a two-factor wear model (contact pressure - sliding velocity) with identification of wear resistance parameters was considered. On the basis of the proposed wear model, the wear-contact problem for a cylindrical sliding bearing was solved. The equation of equilibrium for medium pressures and the approximating function of linear wear from the arc of contact between the shaft and the bushing were used as the determining equations. To identify parameters of wear resistance in the wear model, a calculation-experimental method for determining calculated dependences of wear resistance parameters was developed on the basis of the wear test by the «cone – three balls» scheme. The results of wear tests of bronze conical specimens with a variable wear spot and two values of sliding velocity were taken as a base. The obtained results were recommended for predicting wear of sliding bearings at the design stage and optimizing their design and operational parameters.



  • Keywords

    sliding bearing, wear-contact problem, wear model, wear testing, wear resistance parameters.

  • References

      [1] Chernets, M. V. (2015). Prediction of the life of a sliding bearing based on a cumulative wear model taking into account the lobing of the shaft contour. Journal of Friction and Wear, 36(2), 163-169. doi:10.3103/S1068366615020038

      [2] Soldatenkov, I.A. (2010). Evolution of contact pressure during wear of the coating in a thrust sliding bearing. Journal of Friction and Wear, 31(2), 102-106. doi:10.3103/S1068366610020029

      [3] Mezrin, A.M. (2009). Determining local wear equation based on friction and wear testing using a pin-on-disk scheme. Journal of Friction and Wear, 30(4), 242-245. doi:10.3103/S1068366609040035

      [4] Dykha, A.V., Kuzmenko, A.G. (2016). Distribution of friction tangential stresses in the Courtney-Pratt experiment under Bowden’s theory. Journal of Friction and Wear, 37 (4), 315–319. doi: 10.3103/s1068366616040061

      [5] Bulgarevich, S.B., Boiko, M.V., Lebedinskii, K.S., Marchenko D.Yu. (2014). Kinetics of sample wear on four-ball friction-testing machine using lubricants of different consistencies. Journal of Friction and Wear, 35(6), 531–537. doi:10.3103/S106836661406004X

      [6] Dykha, A.V., Kuzmenko, A.G. (2015). Solution to the problem of contact wear for four-ball wear-testing scheme. Journal of Friction and Wear, 36(2), 138-143. doi: 10.3103/S1068366615020051

      [7] Rezaei, A., Paepegem, W.V., Baets, P.D., Ost, W., Degrieck, J. (2012). Adaptive finite element simulation of wear evolution in radial sliding bearings. Wear, 296(1-2), 660-671.

      [8] Dykha, A. Determining the characteristics of viscous friction in the sliding supports using the method of pendulum [Text] / A. Dykha, V. Aulin, O. Makovkin, S. Posonskiy // Eastern-European Journal of Enterprise Technologies. – 2017. – Vol. 3, Issue 7 (87). – P. 4–10. doi: 10.15587/1729-4061.2017.99823

      [9] Vynar, V.A., Dykha, M.O. (2013). Influence of the stress-strain state on the wear resistance of the surface of 40Kh Steel after discrete electromechanical treatment. Materials Science, 49 (3), 375-381.




Article ID: 11872
DOI: 10.14419/ijet.v7i2.23.11872

Copyright © 2012-2015 Science Publishing Corporation Inc. All rights reserved.